400 bbl Tank Dimensions, Capacity and What to Check Before Buying Used
How big is a 400 bbl tank, how many litres it holds, common shop-built dimensions, and what to inspect before buying used oilfield tanks in Western Canada.
In this guide
Buyer checklist
- 01
Overview
A 400 bbl tank is one of the most common used oilfield tanks offered in Western Canada. Buyers search for its dimensions and for how many litres or cubic metres it holds, then need to know whether the particular tank on a listing will fit the site, the truck and the intended service. This guide explains how capacity is measured, why some shop-built tanks are about 12 ft in diameter and 20 ft high, and what to inspect before you buy.
Browse current used oilfield tanks for sale, including tanks in Alberta and listings around Lloydminster, AB/SK. If the tank is part of a production package, also compare used separators and used pressure vessels.
- 02
How 400 bbl of capacity is measured
In Canadian energy statistics, one petroleum barrel (bbl) is a volume unit. Natural Resources Canada’s conversion factors give 1 bbl as 158.987295 litres, or 0.158987295 cubic metres. On that basis:
The same barrel is 42 US gallons. Oilfield listings in Western Canada almost always use barrels for production and storage tanks, and litres or cubic metres when a drawing, nameplate or engineering package is in SI units. If a listing shows only one unit, convert it and confirm that the figure is the tank’s rated or nominal capacity, not an estimate of the last product volume left in the tank.
Nameplate capacity, geometric (shell) volume and usable working volume are not always the same. Internals, a cone or dish roof, a sump, a high fill alarm or an operating fill height can reduce how much you can actually store. Use the nameplate or the manufacturer’s drawing as the authority for the tank you are buying, and treat a conversion from 400 bbl as a check, not a substitute for that document.
- 400 bbl = 63,594.918 litres, usually stated as about 63,595 litres
- 400 bbl = 63.594918 m³, usually stated as about 63.6 m³
- 03
Typical shop-built dimensions
Many shop-built 400 bbl vertical tanks used in Western Canada are built at about 12 ft in diameter and 20 ft in height. That combination is common because a vertical cylinder of those dimensions has a geometric volume close to 400 bbl (about 403 bbl if you treat the shell as a right cylinder and use 5.61458333 cubic feet per barrel). The extra volume is taken up by roof shape, internals and operating fill, which is why the tank is still described as a 400 bbl tank.
Dimensions vary by manufacturer, year and design. Horizontal tanks, skidded packages, lower-profile tanks and tanks built to a particular specification will not match 12 ft by 20 ft. Frac and flowback tanks are often a different shape again: long, portable, rectangular or rounded-end tanks built to be trucked between locations, not standing vertical production tanks. Always confirm outside diameter or width, shell height, overall height including handrail or thief hatch, skid or base dimensions, nozzle projection and estimated shipping weight for the specific tank.
If you are checking a drawing yourself, use the shell diameter and tangent-to-tangent or straight-shell height, then compare the calculated volume with the nameplate. Ask the seller for a photo of the nameplate and, if they have it, the original drawing or data sheet.
- 04
Production, frac, flowback and mud tanks
Capacity alone does not tell you what the tank was built or used for.
A used 400 bbl production tank is not automatically suitable for frac or flowback service, and the reverse is also true. Match the original design and the previous product to the service you intend. If the listing is unclear, ask the seller to state the original design, the last product stored, and whether the tank was in sweet, sour, produced-water or chemical service.
- Production or storage tanks are usually stationary tanks at a battery or wellsite. Shop-welded steel tanks for storage of production liquids are often built to a specification such as API Spec 12F. Confirm the actual specification on the nameplate or data sheet; not every used 400 bbl tank is an API 12F tank.
- Frac tanks are portable tanks used to hold water or fluids on location during completions. They are designed to be moved frequently.
- Flowback tanks receive fluids returning from the well after a frac and are often built with solids and gas handling in mind.
- Mud tanks are typically open-top tanks used in drilling-fluid systems.
- 05
What to inspect before you buy
Start with photographs and records, then decide whether a site inspection is warranted. Ask for:
Look for floor corrosion, coating failure, pitting, leaks at nozzles, damaged or missing fittings, distorted skids, and repairs that are not documented. Previous sour, produced-water or chemical service can leave corrosion or deposits, including iron sulphide after sour service, and may require cleaning and inspection before the tank goes back into service. A tank that looks tidy from the outside can still have a thin floor.
If you will install the tank in upstream petroleum service in Alberta, check the intended installation against AER Directive 055, including secondary containment and the other storage requirements that apply to your site. Other provinces have their own storage and environmental rules. Directive 055 is an installation and operating requirement for the duty holder; buying a used tank does not by itself satisfy it.
For a broader document list that applies to used equipment generally, see Documents for buying used oilfield equipment in Canada.
- A clear photo of the nameplate, including capacity, year, specification, manufacturer and any registration marks
- Inside and outside photos of the floor, shell, roof, manway, thief hatch, valves and fittings
- Ultrasonic thickness (UT) readings, especially on the floor and lower shell, with the date and the locations measured
- The condition of the internal coating or lining, if one was applied, and any coating specification
- Cleaning history and the last product stored
- Any inspection, repair or alteration reports
- 06
Moving a used 400 bbl tank
Most 400 bbl vertical tanks are moved by winch tractor or bed truck. A tank about 12 ft wide is already at a width that often requires oversize permits, and overall height, weight and the loaded length of the truck will also matter. Confirm:
In Alberta, commercial oversize and overweight moves are permitted under the province’s weight and dimension and oversize and overweight permit rules. Saskatchewan, British Columbia and Manitoba have their own permit rules. Have the carrier confirm the route and the permits for every jurisdiction on the move. Planning pickup of used oilfield equipment in Alberta covers measurements, loading and the collection handoff in more detail.
Do not treat a listing photo as a substitute for confirmed shipping measurements. A handrail, nozzle or thief hatch can change the loaded height, and a tank that still contains product or sludge is a different lift than a clean, empty tank.
- Shipping dimensions and a weight, or an agreed method for obtaining them
- Skid or base type, lifting lugs and whether the tank is ready to load
- Who is responsible for cleaning, loading, transport, permits and unloading
- The yard or lease location, access and any site constraints
- 07
Buying on Redeploy HQ
Redeploy HQ lists used and surplus tanks from operators, service companies and equipment dealers across Alberta, Saskatchewan, British Columbia and Manitoba. Compare capacity, previous service, seller location and the records the seller can provide, then confirm transport from the yard before you agree on a price. Start with the tanks category or the Alberta tanks page, and use the listing location to estimate the move, including tanks around Lloydminster.
Common questions
How many litres are in a 400 bbl tank?
Using Natural Resources Canada’s conversion of 158.987295 litres per barrel, 400 bbl is 63,594.918 litres, or about 63.6 m³. Confirm the nameplate capacity for the specific tank, because usable volume can be lower than the nominal 400 bbl figure.
Are all 400 bbl tanks 12 ft by 20 ft?
No. Many shop-built vertical 400 bbl tanks are about 12 ft in diameter and 20 ft high, and a cylinder of those dimensions has a geometric volume close to 400 bbl. Horizontal tanks, portable frac tanks and other designs will differ. Confirm the drawing or nameplate.
Does a used 400 bbl tank include fittings and a skid?
Not always. Some sales are the shell only; others include the skid, valves, thief hatch, stairs or internal lining. Ask the seller for a written list of what is included and inspect those items in the photos or on site.
Can I put a used production tank into frac or flowback service?
Only if the original design, current condition and previous service suit that use. A stationary production tank and a portable frac or flowback tank are built for different duties. Confirm the design and ask a qualified reviewer if you are changing service.
Do I need oversize permits to haul a 400 bbl tank?
Often yes, because a 12 ft-wide tank already exceeds common legal width, and height or weight may also be over the unpermitted limit. The carrier should confirm dimensions, weight and permits for each province on the route.
Continue your equipment search
Sources and further reading
Check the current guidance for the equipment, location and work involved.
- Natural Resources Canada: conversion factors and common units
- AER Directive 055: Storage Requirements for the Upstream Petroleum Industry
- Alberta: commercial vehicle weight and dimension permits
- Alberta: commercial vehicle oversize and overweight permits
- API Spec 12F, Specification for Shop-welded Tanks for Storage of Production Liquids