Rig Mat Sizes and Types: 8x40 vs 8x20, Steel-Frame vs Laminated
Compare 8x20 and 8x40 rig mats, laminated and steel-frame construction, and what to inspect before buying used oilfield mats in Western Canada.
In this guide
Buyer checklist
- 01
Overview
Rig mats, also searched as oilfield mats or access mats, spread load and protect the ground under rigs, leases, access roads and work areas. Buyers in Western Canada often compare 8 × 20 ft and 8 × 40 ft mats, then have to choose between laminated timber mats and steel-frame (cross-beam) construction. This guide explains those sizes and types, and what to inspect on a used mat before you buy.
See current rig mats for sale, including rig mats in Alberta. If you are building a lease or moving a rig, also browse used drilling rigs.
- 02
What a rig mat is for
A rig mat is a portable timber or composite panel used to create a working surface on soft, wet or uneven ground. Typical jobs include drilling and service-rig leases, access roads, pipeline crossings, wellsite work areas and temporary pads. The useful questions are the size of each mat, how it is built, how neighbouring mats connect, the manufacturer’s load rating for the intended use, and the condition of the timber, steel and hardware after previous jobs.
Load rating depends on the design, the supporting ground, the span or unsupported width, and the type of load (static equipment, truck traffic, or a concentrated crane or rig load). This guide does not quote load ratings. Ask the seller for the manufacturer’s rating and the intended use, and have a qualified person confirm that the mats suit your ground conditions and equipment.
- 03
Common sizes: 8 × 20 ft and 8 × 40 ft
Buyers and listings in Western Canada often describe mats as 8 × 20 ft or 8 × 40 ft. Those two sizes are convenient to compare: an 8 × 40 ft mat covers twice the length of an 8 × 20 ft mat at the same width, so a pad plan usually works in multiples of 8 ft of width and 20 ft of length.
They are not the only sizes available. An Alberta manufacturer of laminated and cross-beam mats, for example, publishes widths of 8 to 12 ft and lengths of 10 to 60 ft. Used inventory may also include 8 × 16 ft mats or other cuts. Always confirm the actual width, length and thickness of the mats in the lot, not only the size in the title.
When you compare 8 × 20 and 8 × 40:
- Transport. An 8 ft-wide mat is already a wide load once it is on a trailer. A 40 ft mat is longer to haul and to handle than a 20 ft mat. Confirm how the seller ships them (flatbed, bundle count, whether they will load) and whether oversize permits apply. See Planning pickup of used oilfield equipment in Alberta and Alberta’s oversize and overweight permit rules. Other provinces have their own permit requirements.
- Handling. Confirm lifting points, whether the mats have lift rings or slots, and what equipment is needed in the yard and on the lease.
- Pad layout. Longer mats can reduce the number of joints in one direction. Shorter mats can be easier to place in tight access or to replace one-for-one if a single mat is damaged.
- Lot consistency. A used lot may mix sizes or pair 20 ft mats that were once used as a 40 ft run. Count the pieces, measure a sample, and confirm that the lot you are buying is the lot in the photos.
- 04
Laminated mats and steel-frame mats
Two construction styles show up often in Western Canadian used inventory.
Laminated timber mats are built from layers of dimensional lumber, typically with steel or pipe members along the ends or beams. A published Alberta example uses kiln-dried 2 × 6 lumber with pipe beam ends and two-, three- or four-beam options. The working surface is timber. These mats are widely used for access and lease work. Condition of the lumber — cracks, breaks, soft spots, missing pieces and fastener condition — is the main inspection point, along with the end steel.
Steel-frame or cross-beam mats combine a steel frame or cross-beams with timber decks. A published Alberta example uses pipe or I-beam ends with 6 × 6 timbers through the mat, and is described as repairable. The steel frame carries more of the structure; the timber still has to be sound and properly fastened. Inspect the welds, beams, lifting hardware and timber equally.
Other types exist, including interlocking mats and plastic or composite mats. If a listing says “composite” or “interlocking,” ask for the manufacturer, the connection method and the load rating. Do not assume a composite mat and a timber mat are interchangeable for the same rig or crane load.
Used mats are often repaired. A repair is not automatically a defect, but undocumented or uneven repairs, replaced boards that are not fastened to the same standard, and bent or cracked steel should be treated as part of the condition, not as a cosmetic issue.
- 05
What to inspect on a used lot
Ask the seller for:
On inspection, check timber for broken or missing boards, crushing, rot or soft fibres, and oil or chemical contamination that may matter for your next site. Check steel for cracks, bent beams, failed welds and seized or missing lift hardware. Check that the mats in the stack match the count and the size you were offered. If only the top of a stack is visible, ask to see more of the lot or treat the unseen mats as unverified.
Thickness and remaining timber section affect both strength and how the mats sit against each other. A worn mat may still be useful for light access work and unsuitable under a rig or a concentrated load. Say what you intend to use them for when you ask for a rating.
- The number of mats, the size of each, and whether the lot is all one size and type
- Manufacturer, if known, and any available load-rating or specification sheet
- Photos of a representative sample: top, bottom or underside if it can be turned, ends, lifting points and any obvious damage
- How the mats have been used (lease, access road, crane pad) and how they have been stored
- Whether hardware, pins, bolts or lift rings are included
- 06
Transport, storage and site use
Mats are heavy, and a full truck is a planned lift at both ends. Confirm who loads and unloads, the equipment on site, and whether the mats will be bundled or loose. An 8 ft width often requires a permit; length and weight may as well. Stack mats on level, well-drained ground so they do not sit in water, and follow the manufacturer’s guidance for lifting.
If the mats will go under a drilling or service rig, coordinate the pad plan with the rig move and with any drilling rig or lease-construction requirements you already have. The mat specification and the ground preparation belong together; one does not replace the other.
- 07
Buying on Redeploy HQ
Redeploy HQ lists used rig mats from Western Canadian sellers when they are offered. Compare size, construction, condition and location on the rig mats category page and on the Alberta rig mats page. Confirm the piece count, the measured size and the loading arrangement before you book transport.
Common questions
What is the difference between an 8 × 20 and an 8 × 40 rig mat?
Both are 8 ft wide. The 40 ft mat is twice as long, so it covers more ground in one piece and is longer to haul and to handle. An 8 × 20 ft mat is easier to place in tight access and to replace individually. Confirm the actual measurements; other lengths are also sold.
What is the difference between laminated and steel-frame rig mats?
Laminated mats are built mainly from layered timber, usually with steel or pipe at the ends or beams. Steel-frame or cross-beam mats use a steel frame or cross-members with a timber deck. Ask for the manufacturer’s description and inspect both the timber and the steel on a used mat.
Do used rig mats come with a load rating?
Sometimes the manufacturer’s rating is still available; often it is not on a used lot. Ask the seller for any specification sheet and describe your intended use. Do not assume a used mat still carries its original rating if the timber or steel is damaged.
Are oilfield mats and rig mats the same thing?
Buyers use both terms, and “access mats” or “swamp mats” also appear in listings. The useful distinction is size, construction and intended load, not the marketing name. Read the listing details and ask if the name is unclear.
Can I haul 8 ft-wide mats without a permit?
Not necessarily. An 8 ft-wide load can already require an oversize permit once it is on a trailer, and length or weight may also be over the unpermitted limit. The carrier should confirm the loaded dimensions and the permits for each province on the route.
Continue your equipment search
Sources and further reading
Check the current guidance for the equipment, location and work involved.